Calculation methods

Hydrogen Calculation Methods

Formulas and assumptions behind our electrolyzer, fuel cell, hydrogen storage, and pipeline calculators.

Carbon intensity of hydrogen

Carbon Intensity (kg CO2e/kg H2) = kWh/kg H2 × grid factor · Total (kg CO2e) = intensity × volume · Total (t CO2e) = kg ÷ 1,000

The carbon intensity of electrolytic hydrogen is driven by the electricity source, not the electrolyzer itself. Carbon Intensity (kg CO2e per kg H2) = Specific Energy Consumption (kWh/kg H2) × Grid Region Emission Factor (kg CO2e/kWh); at 55 kWh/kg and the national average factor of 0.370, that is 20.35 kg CO2e per kg. Total Emissions for Production Volume (kg CO2e) = Carbon Intensity × Hydrogen Production Volume (kg); at 20.35 and 1,000 kg, that is 20,350 kg CO2e. Total Emissions (metric tons CO2e) = kg ÷ 1,000 — 20.35 t CO2e. The grid region emission factors are the same EPA eGRID2023 regional averages used on our Carbon Emissions Calculator, so the two tools share a consistent methodology. The same electrolyzer can swing roughly 4x in carbon intensity between a clean grid like Upstate New York (0.110) and a coal-heavy grid like the Upper Midwest (0.420) — which is why grid-powered electrolysis can be more carbon-intensive than gray hydrogen (9-12 kg CO2e/kg) unless the electricity is genuinely low-carbon.

Open the calculator →

Electrolyzer efficiency

System Efficiency (% HHV) = (39.4 ÷ kWh/kg H2) × 100 · Daily (MWh/day) = (kg/day × kWh/kg) ÷ 1,000 · Annual (MWh/yr) = Daily × 365

Electrolyzer efficiency compares the electricity a real system consumes against the thermodynamic minimum needed to split water. System Efficiency (% HHV) = (39.4 kWh/kg ÷ Specific Energy Consumption (kWh/kg H2)) × 100, where 39.4 kWh/kg is hydrogen’s higher heating value — the theoretical minimum energy to split water, including the heat released when the product water condenses. At 55.2 kWh/kg (a typical PEM system), efficiency is (39.4 ÷ 55.2) × 100 = 71.4%; at 40.0 kWh/kg (a solid oxide system using external waste heat), it rises to 98.5% on an HHV basis. The gap between the theoretical minimum and real consumption is lost to stack resistance, heat, gas processing, and balance-of-plant parasitic loads. Daily Electricity Consumption (MWh/day) = (Hydrogen Production Rate (kg/day) × Specific Energy Consumption (kWh/kg H2)) ÷ 1,000; at 1,000 kg/day and 55.2 kWh/kg, that is 55.2 MWh/day. Annual Electricity Consumption (MWh/year) = Daily × 365 — 20,148 MWh/year at the defaults. Efficiency is reported on an HHV basis, the industry-standard convention for electrolyzers; fuel cells conventionally use hydrogen’s lower heating value (LHV) instead. Electrolyzer stacks also degrade over time — PEM specific energy consumption can rise up to roughly 10% above start-of-run conditions after about 60,000 hours, which is factored into stack replacement planning.

Open the calculator →

Hydrogen fuel cell output

Electrical Output (kWh) = H₂ (kg) × 33.3 kWh/kg (LHV) × efficiency · Avg Power (kW) = Output ÷ hours · Waste Heat (kWh) = H₂ × 33.3 × (1 − efficiency)

This calculator ties the electricity a fuel cell delivers to how much hydrogen is available, how efficiently it converts that hydrogen, and how long it runs. Electrical Energy Output (kWh) = Hydrogen Available (kg) × 33.3 kWh/kg (LHV) × (Fuel Cell Efficiency (%) ÷ 100), where 33.3 kWh/kg is hydrogen’s lower heating value — the usable energy content when the water vapor produced leaves the system without condensing, which reflects how most fuel cells actually operate. At 100 kg and 55% efficiency, that is 100 × 33.3 × 0.55 = 1,831.5 kWh (about 18.3 kWh per kg). Average Power Output (kW) = Electrical Energy Output (kWh) ÷ Operating Duration (hours); at 1,831.5 kWh over 10 hours, that is 183.15 kW. Waste Heat Output (kWh) = Hydrogen Available (kg) × 33.3 kWh/kg (LHV) × (1 − Fuel Cell Efficiency (%) ÷ 100); at 100 kg and 55% efficiency, the remaining 45% becomes 100 × 33.3 × 0.45 = 1,498.5 kWh of waste heat — which combined heat and power (CHP) configurations can capture to push total system efficiency above 80%. Efficiency is reported on an LHV basis, the industry-standard convention for fuel cells; electrolyzers conventionally use hydrogen’s higher heating value (HHV, 39.4 kWh/kg) instead. Data sources: fuel cell manufacturer specifications (Plug Power, Ballard, Bloom Energy, others); DOE hydrogen and fuel cell program reports; NREL fuel cell efficiency benchmarks; CHP system analysis.

Open the calculator →

Hydrogen compression energy

Total Energy (kWh) = H₂ mass (kg) × intensity (kWh/kg) · % of HHV = (intensity ÷ 39.4 kWh/kg) × 100

This calculator ties the energy required to compress hydrogen to how much hydrogen you are compressing and how energy-intensive that compression is per kilogram. Total Compression Energy Required (kWh) = Hydrogen Mass to Compress (kg) × Compression Energy Intensity (kWh/kg H₂); at 1,000 kg and 2.8 kWh/kg (the 700 bar value), that is 1,000 × 2.8 = 2,800 kWh. Compression Energy as % of Hydrogen’s Energy Content (HHV) = (Compression Energy Intensity (kWh/kg H₂) ÷ 39.4 kWh/kg) × 100, where 39.4 kWh/kg is hydrogen’s higher heating value — the total energy content of a kilogram of hydrogen; at 2.8 kWh/kg, that is (2.8 ÷ 39.4) × 100 = 7.1%, meaning compressing hydrogen to 700 bar consumes roughly 7% of the energy the hydrogen itself carries. Compression energy intensity rises with target pressure because compression is fundamentally a heating process, so multi-stage compressors with intercooling between stages keep temperatures below roughly 200°C while reaching high final pressures — reaching 700 bar typically requires at least 4 stages. The 440 bar (2.23 kWh/kg) and 880 bar (3.0 kWh/kg) values are sourced directly from DOE hydrogen compression energy studies; the 350 bar (2.0 kWh/kg) and 700 bar (2.8 kWh/kg) values are reasonable interpolated estimates. Data sources: U.S. Department of Energy (DOE) hydrogen compression energy studies; hydrogen refueling station design specifications; multi-stage compressor engineering literature; fuel cell vehicle tank pressure standards (SAE J2601).

Open the calculator →

Hydrogen pipeline loss

Lost (kg) = transported (kg) × (leakage % ÷ 100) · Delivered (kg) = transported − lost · $/shipment = lost × $/kg · Annual $ = $/shipment × shipments/yr

This calculator ties the hydrogen lost during pipeline transport to how much hydrogen is moved, the pipeline leakage rate, the value of the hydrogen, and how many shipments happen per year. Hydrogen Lost in Transport (kg) = Hydrogen Transported (kg) × (Pipeline Leakage Rate (%) ÷ 100); at 10,000 kg and a 0.4% leakage rate, that is 10,000 × 0.004 = 40 kg lost per shipment. Hydrogen Delivered (kg) = Hydrogen Transported − Hydrogen Lost in Transport; at 10,000 kg and 40 kg lost, that is 9,960 kg delivered. Value of Lost Hydrogen per Shipment ($) = Hydrogen Lost in Transport (kg) × Hydrogen Value ($/kg); at 40 kg and $4.00/kg, that is 40 × 4.00 = $160 per shipment. Annual Value of Lost Hydrogen ($) = Value of Lost Hydrogen per Shipment × Shipments per Year; at $160/shipment and 300 shipments/year, that is 160 × 300 = $48,000/year. The leakage rate is the single most decision-relevant input: a referenced study found leakage rates around 0.4% for dedicated steel hydrogen pipelines specifically, well under the Environmental Defense Fund’s already-conservative 1% best-case value-chain estimate, while non-metallic (plastic) pipe can leak roughly 1,000x more than austenitic steel. The bigger leakage risk often sits elsewhere in the value chain — electrolysis production venting, liquid hydrogen boil-off, and road transport/storage can outweigh pipeline transport itself. Hydrogen leakage also matters for climate, not just economics: hydrogen acts as an indirect greenhouse gas by extending the atmospheric lifetime of methane. Data sources: referenced hydrogen pipeline leakage study (0.4% steel pipeline rate); Environmental Defense Fund hydrogen value-chain leakage estimates; pipeline material comparison research (polyethylene vs. austenitic steel); hydrogen supply-chain leakage projections from NREL and IEA; hydrogen climate impact research (indirect radiative forcing).

Open the calculator →

Hydrogen storage tank sizing

Volume (m³) = H₂ mass (kg) ÷ density (kg/m³) · Volume (gal) = Volume (m³) × 264.172

This calculator ties the physical tank volume required to store hydrogen to how much hydrogen you need to store and how densely that hydrogen can be packed at the chosen pressure or phase.

Data sources: Hydrogen storage density values from DOE hydrogen storage technology assessments; compressed gas storage specifications from tank manufacturers; cryogenic liquid hydrogen properties from NIST and aerospace engineering references; fuel cell vehicle tank pressure standards (SAE J2601).

Read the full explanation on the calculator page →

Power-to-Gas efficiency

H₂ (kg) = electricity in (kWh) ÷ kWh/kg · Output (kWh) = H₂ × 33.3 (LHV) × FC efficiency · Round-trip (%) = (output ÷ input) × 100

This calculator traces electricity through a full power-to-gas-to-power round trip: into an electrolyzer that makes hydrogen, then back out through a fuel cell that converts that hydrogen into electricity again. Hydrogen Produced (kg) = Electricity Input (kWh) ÷ Electrolyzer Specific Energy Consumption (kWh/kg H₂); at 1,000 kWh and 55.2 kWh/kg (a typical PEM system), that is 1,000 ÷ 55.2 = 18.12 kg. Electricity Output (kWh) = Hydrogen Produced (kg) × 33.3 kWh/kg (LHV) × (Fuel Cell Efficiency (%) ÷ 100), where 33.3 kWh/kg is hydrogen’s lower heating value; at 18.12 kg and 55% efficiency, that is 18.12 × 33.3 × 0.55 = 331 kWh. Round-Trip Efficiency, Power-to-Power (%) = (Electricity Output ÷ Electricity Input) × 100; at 331 kWh out and 1,000 kWh in, that is 33.1%. Each conversion step loses energy — electrolysis around 70% efficiency and fuel cells around 50-60% — so the combined round trip lands around 30-40%, well below a lithium-ion battery’s 85-92%. Hydrogen’s case is not round-trip efficiency but storage duration: it can store energy economically for weeks or months, something batteries cannot do at scale. Data sources: NREL electrolyzer efficiency studies; PEM fuel cell technology assessments; hydrogen LHV (33.3 kWh/kg); lithium-ion battery round-trip efficiency research; IEA and DOE power-to-gas system modeling.

Open the calculator →

← All calculation methods